ALL OF THE SA-200 SERIES SMOKE SYSTEM OIL TANKS ARE THE SAME SIZE (DIMENSIONS).  MODELS DIFFER BY OIL SUCTION TUBE DESIGN, OIL PUMP MOUNTING LOCATION AND OIL TANK CONFIGURATION.

ANY SIDE OF THESE TANKS CAN BE THE TOP SIDE.  CALL WITH YOUR IDEA.

NO WELDING NEEDED, INSTALL KITS USING BASIC TOOLS

 

 

SA-200

 

(*shown with optional Remote Switch Kit)

DIMENSIONS

HEIGHT (TO TOP OF FILL CAP) = 14"

WIDTH (END WHERE OIL PUMP IS MOUNTED) = 10"

DEPTH (PUMP TO OPPOSITE END OF TANK) = 17.25"

NOTE:  ADD 1.5" AT BASE OF TANK ON SIDES AND ENDS FOR BRACKET WIDTH.

______________________________________________

 

SA-201

 

(*shown with optional Remote Switch Kit)

 

DIMENSIONS

HEIGHT (TO TOP OF FILL CAP) = 14"

WIDTH (END WHERE OIL PUMP IS MOUNTED) = 10"

DEPTH (PUMP TO OPPOSITE END OF TANK) = 17.25"

NOTE:  ADD 1.5" AT BASE OF TANK ON SIDES AND ENDS FOR BRACKET WIDTH.

____________________________________________

 

SA-200 AND 201T

OIL PUMP MOUNTED ON TOP

THIS PARTICULAR KIT HAS BEEN INSTALLED IN THE BAGGAGE AREA OF A CJ6A, T34A AND RV7 TO DATE.  USE THIS KIT WHEN HEIGHT IS NOT AN ISSUE. 

DIMENSIONS

HEIGHT (TO TOP OF OIL PUMP) = 16 1/4"

WIDTH (LEFT TO RIGHT) = 13"

DEPTH (END WITH LABEL) = 10"

NOTE:  ADD 1.5" AT BASE OF TANK ON SIDES AND ENDS FOR BRACKET WIDTH.

______________________________________________

 

SAMPLE OF

SA-200 OR 201 WITH MODIFIED FILL CAP PLACEMENT

THIS PIC IS OF A TYPICAL YAK 52 SETUP WITH THE OIL TANK INSTALLED BEHIND THE VERTICAL SUPPORT THAT IS LOCATED BEHIND THE REAR SEAT.  INSTALLATION ACCESS IS GAINED THROUGH THE COVER UNDER THE REAR MOST WINDOW.  THE OIL PUMP WILL BE LOCATED NEAR THE TWO AIR BALLS ON THE RIGHT SIDE OF THE FUSELAGE (YOU ARE LOOKING AT THIS SYSTEM FROM THE FRONT). 

FEATURES:

 

• FILL CAP IN CENTER OF OIL TANK FOR EASY FILLING THROUGH ACCESS COVER UNDER REAR MOST WINDOW
• SUCTION TUBE CENTER/REAR OF OIL TANK FOR BEST PICKUP

 

• FOR LEVEL AND NON-CONTINUOUS INVERTED, POSITIVE G FLIGHT
• ANY DIMENSION TOP
• PUMP CAN BE MOUNTED ON TOP OR ANY SIDE
• FILL CAP AND OTHER FITTINGS INSTALLED WHERE YOU WANT THEM
• ALL HARDWARE INCLUDED FOR COMPLETE INSTALLATION

• CONTINUOUS INVERTED FLIGHT
• ANY DIMENSION TOP
• PUMP MOUNTED ON TOP OR ANY SIDE
• FILL CAP AND OTHER FITTINGS INSTALLED WHERE YOU WANT THEM
• ALL HARDWARE FOR COMPLETE INSTALLATION

• SAME AS SA-200 AND 201 EXCEPT THE OIL PUMP IS MOUNTED ON THE TOP OF THE OIL TANK INSTEAD OF BRACKET MOUNTED ON THE SIDE

OIL TANK CAPACITY SA-200 SERIES KITS	APPROXIMATE GALLONS OF OIL USED PER MINUTE	APPROXIMATE TOTAL RUN TIME AT BEST OIL MIXTURE VALVE SETTING (turn valve down and add more run time!)
5.5 US GALLONS	.8	7+ MINUTES

OIL TANK EMPTY Includes mounting brackets and hardware, oil pump w/bracket, flop tube, vent system etc.	OIL TANK FULL Includes mounting brackets and hardware, oil pump w/bracket, flop tube, vent system etc.	OIL PUMP Includes side mount bracket and hardware.	COMPONENTS Hoses, switches, valve, injector, etc. (includes Remote Switch Kit)	SA-200 SERIES KITS TOTAL WEIGHT FULL (everything included)
15 POUNDS	56 POUNDS	5 POUNDS	3 POUNDS	59 POUNDS